Maytronics Bottom Lid With Fine Filter (F5)

About this part

What it does and when to replace it.

This genuine Maytronics assembly pairs a bottom lid with an integrated fine filter. It captures fine debris during cleaning to help maintain filtration and debris collection.

Compatibility is confirmed for Dolphin Premier. Part 9991456-ASSY replaces a bottom lid that is worn, damaged, or missing. Poolbots does not currently stock this part in its own store. For help identifying it and checking fit before installation, contact Poolbots' pool experts via live chat or phone.

Pool expert tips

Use the full part number, 9991456-ASSY, when identifying this assembly.
The spec sheet lists other model names. Confirm fit before using this part on a model other than Dolphin Premier.

Compatibility

Fits these Dolphin robots.

Confirmed by Maytronics' compatibility checker and each robot's own spare-parts list.

Sold here

Dolphin Premier

Pools to 50 ft · Floor, Walls and Waterline · 3-yr warranty

$1999 free shipping

Shop 20 parts Fixes Warranty

Also listed by Maytronics for: Dolphin Premier, Dolphin Triton 2014, Dolphin XT3, Dolphin XT2, Wave 30, Dolphin Wave 30.

Do it yourself

How to replace it at home.

Switch off and unplug the power supply.
Remove the cleaner from the pool and position it so you can access the bottom lid.
Follow your cleaner's instructions to remove the old bottom lid assembly.
Install the replacement assembly according to your cleaner's instructions.
Check that the lid is secure before returning the cleaner to the pool.

Step-by-step answers for this kind of part

How do I replace the filter panels on my Dolphin robot?Video15 min

Find your model below, then follow its video and instructions. The panel removal and installation steps vary by filter design.

S50 (Cayman, T15, T25, Active 10, Escape, Encore, E20, E25) & S100 (Advantage, Proteus DX3, Saturn, Echo, Nautilus CC, Active 15, Escape, Liberty 200/300/400)

Step 1Remove the old filter panels

Lift the filter cover open.
Take the filter basket out of the robot.
Press the plastic release at the top of the filter's wide side, then lift out the released panel. The narrow side panels come out easily. The front and back panels are secured with screws, so use a Phillips-head screwdriver to release them.
Follow the same process for the opposite side panel.

Step 2Install the replacement panels

Slide a replacement panel into the basket.
Push the panel against the frame until it clicks into place.
Fit the other side panel the same way.
With both panels in position, clip the filter's bottom section back into place.

S200 (E30, Advantage Ultra, Active 20, Quantum, T30, Proteus DX4, Triton PS) / S300 (E35/E35i, Proteus DX5i, Active 30, T35/T45, Premium 40, Explorer E30, E40i, Active 30i, T55i) / S400 (E50i, Active 50, Explorer E50) / Liberty 600

Step 1Remove the old filter panels

Lift the filter cover open.
Take the filter basket out of the robot.
Press the plastic release at the top of the filter's side, then lift out the panel that releases.
Work through the remaining narrow and wide panels using the same method.

Step 2Install the replacement panels

Set the bottom edge of a replacement panel into the filter's lower rail.
Push the panel into the frame so it clips into the filter.
Press it against the frame until you hear it click.
Fit each remaining narrow and wide panel the same way.

Premier/Dx4 (Bag filter)

Filter bag setup for Dolphin Premier

Turn the robot upside down so you can reach the filter area.
Release the clips underneath the filter assembly.
Lift the assembly out of the robot.
If the white filter screen is not already fitted, secure it with the two screws.
Check that the filter bag sits securely on the assembly's guard rails.
Put the filter bag assembly back in, following the guide and video.

Filter cartridge assembly setup for Dolphin Premier

Turn the robot upside down so you can reach the filter area.
Release the clips underneath the filter assembly.
Lift the assembly out of the robot.
Make sure the white filter screen is not installed for this setup.
Follow the guide and video to reinstall the assembly.
Fasten the clips underneath the assembly to secure it.

M250 (Dx3, Nautilus CC Plus)

Step 1Prepare the filter cartridges

Lift the filter covers and take the cartridges out of the robot.
Release the clips at the top of each cartridge.
Inspect the non-return flap for debris.
Check that the frame is clean before fitting replacement panels.

Step 2Fit the replacement panels

Seat the locating tabs along the bottom of each panel in the matching grooves on the base frame.

M400/M500 (Sigma, Nautilus CC Supreme, Aquarius XL, Oasis)

Step 1Prepare the filter cartridges

Lift the filter covers and take the cartridges out of the robot.
Release the clips at the top of each cartridge.
Inspect the non-return flap for debris.
Check that the frame is clean before fitting replacement panels.

Step 2Fit the replacement panels

Seat the locating tabs along the bottom of each panel in the matching grooves on the base frame.

M600/M700 (Active 60, E60i, Premium 60, Explorer E70)

Step 1Remove the old filter panels

Lift the filter cover open.
Take the filter basket out of the robot.
Press the plastic release at the top of the filter's side, then lift out the panel that releases.
Work through the remaining narrow and wide panels using the same method.

Step 2Install the replacement panels

Set the bottom edge of a replacement panel into the filter's lower rail.
Push the panel into the frame so it clips into the filter.
Press it against the frame until you hear it click.
Fit each remaining narrow and wide panel the same way.

Replacement panels and filter care

You can purchase replacement filter panels from Poolbots. Before ordering, confirm that the panel part number matches your robot. For help choosing the correct panels, contact Poolbots' pool experts by live chat or phone.

Additional references:

Open this answer on its own page →

Specifications

Size & Dimension

Gross Weight: 1.103 lb

General Info

Warranty (years): 1
UPC: 9353664009881

Questions